GReddy Turbo Kit Acura RSX Type-S DC5 (K20A) T517Z 8cm2
3-3 Power Steering Line Modification Remove the power steering bracket off the line and valve cover. Bend the Power steering line so that the line r
3-5 Exhaust Manifold Installation (1) Install three stud bolts on to the cylinder head as shown. (Parts used #67) (2) Install
3-7 Oil Pressure Line Connection (1) Connect the oil pressure line that was installed in step 3-4 to the turbo using banjo fitting and copper washe
(5) Modify the drive shaft heat shield by cutting the shaded area in the picture to prevent the hose from rubbing up on the shield. • Reins
(3) Install compression pipe C-2, and C-3 between C-1 and throttle body. Using provided hose and clamps. * Secure the bracket on C-2 to the factor
(5) Install the provided intake air temperature sensor grommet to the suction pipe S-1 as shown. IAT Sensor Grommet (Parts used #4, 56)
3-11 Down Pipe Installation (1) Install three stud bolt on the turbine housing as shown. (Parts used #64) (2) Check the fitment
(2) Install the down pipe heat shield on to the downpipe using the provided M6 x 10mm bolts. (Parts used #48,57) 3-13 Fuel Injectors I
3-14 e-Manage Installation (1) Remove the cover under the glove box to access the ECU and ECU harness. (2) Install the Grey wire to the e-Manage I
86 4 2 73 7 910 13 115 6 184 23 222 225 6 29311 2 3 4 5 68 10 4113 15168 117 2221 23 241 2 3 4 5 6 7 9 11 110 2 16 1529 118 20 1 23 223 4
Acura RSX Type-S DC5 (K20A) T517Z 8cm2 Installation Manual Please read the entire manual before installing this kit. Application: Make
e-manage Factory ECU Pin # Wire Color Description ECU Pin # Color Code3 White MAP IN A19(harness) Green/Red MAP 4 Grey Throttle A15 Red/Black TPS
3-16 Starting the Engine (1) Refill the engine oil to factory spec. (2) Check all the hoses and wires connection, then reconnect the negative side
e-manage Information Important! • The e-manage included in this kit is preprogrammed for the this turbo kit. • Do not attempt to adjust any of the
Incorrect wiring or disconnected Airflow Signal 1Airflow Signal 1input errorAirflow voltageoutput errorNo Injector pulse from allNo Injec
1. Parts List 1. Turbocharger T517Z 8cm2 P565 1 2. Turbo Exhaust Manifold (Cast Iron) 1 3, Down Pipe
1. Parts List 28. Vacuum Hose (Blue) 5∅ x 200mm (for Actuator) 1 29. Rubber Hose 8Ø X 500mm (for Idle controller)
1. Parts List 57. M6 X 10 P=1.0 B S/W F/W - (Down pipe heat shield) 2 58. M6 X 15 P=1.0 B S/W F/W - (Suction pipe & compre
1. Parts List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15-16 17 18 19 20 21 22 23 24 25 26
1. Parts List 27 28~31 32 33~34 35~40 41 42 43 44 45 46 47 48 49 50~51 52 53 54 55 56 57~67
2. Removal of Stock Parts When removing the stock parts, make sure you read over the factory repair manual for proper procedures. 2-1 Disconnect
3. Kit Installation 3-1 Factory heat shield modification (1) Heat shield plate modification Trim the shaded area on the heat shield plate that was
Comentarios a estos manuales